Can I Repair Coffee Pot Leak With Flex Seal

Practise you have a Leaking Cuisinart Coffee Maker? Our programmable Cuisinart coffee maker began to leak water out on the counter top overnight and the pot would come up upwards 2-three cups short. I don't want to purchase another coffee maker if I tin can prepare it. I figured out how to get those security screws out of the bottom cover and fix that leaky hose. Read along to learn how you can too!

This repair is how to fix your coffee maker without replacing the hoses. Of import UPDATE: I accept identified an equivalent replacement hose and I recommend you social club replacement hoses and follow the steps in the commodity linked here instead:

Cuisinart Water Leak Repair-Replace Croaky Water Hoses

How to Repair a Leaking Cuisinart Coffee Maker

Equipment:

Cuisinart DCC-2600 Brew Central 14-Cup Programmable Coffeemaker with Glass Carafe (now replaced by the DCC-2650 model)

Tools Needed:

Needle nose pliers (for removing the hose clamp)
CR-VT10 Security Torx Driver (get as a set or private tool) (must take a thin shaft to fit downwardly into the recessed pigsty)
Size 3 apartment precision screwdriver (this can be used to remove the security torx screws)
Cordless Drill (I honey my Makita)
Drill Bits (if yous end up demoing a fleck of the internals to re-use your old hose)
Wire nipper (for clipping out the plastic webbing to brand the path for the old hose shorter–this is a cracking tool if you exercise any electronics work)

Parts (optional, I repaired mine with no parts necessary):

High temperature silicone tubing .312 ID X .472

Repair Instructions:

Step 1: Unplug the coffee maker.

We are going to open it up and so you lot definitely practise not want it plugged in as y'all could exist shocked.

Stride ii: Empty any water out of the tank.

I just turned mine upside down over the sink.

Step three: Lay the java maker on its dorsum and then you can access the screws on the bottom.

We want to remove the bottom plate. The screws are located in recessed holes located as indicated below. You do not need to remove any of the safe feet to admission the screws, btw.

Cuisinart DCC-2600 Bottom Screw Locations — Spiral Locations

Footstep iv: Remove the four lesser screws.

These screws are security Torx-ten headed screws. This means they are Torx-10 with an additional pivot that sticks up in the middle of the screw caput. Here you lot can see a close-upwardly of the screw head:

Close-up of the security screws — Close-upward of the security screws

The scrap tip for these screws looks like this, a torx with a hole in the middle:

T10 Security Bit Close-Up — Here is what the torx-10 security bit tip looks like

Unfortunately, the pigsty in the instance is too small to utilize a bit tip like the i pictured above, as it won't fit deep enough into the narrow-diameter pigsty. Lucky for us, you can use a 3mm precision flat-tip screwdriver bit instead, which barely fits down into the corners of the star shape:

Flat tip screwdriver fitting in a security T10 Screw Head — The correct size flat-tip screwdriver will fit

I as well discovered that you lot tin can alternatively apply a smaller flat-tip screwdriver bit, which will slip past the security mail and sink down into the caput. Once you lot remove the four screws, you may need to skid a flat-head screwdriver up into the seam to get the lesser out. Hither the lower cover has been removed:

Bottom cover removed (inside) — Lesser embrace removed (within surface)

Here is what information technology looks like within:

Cuisinart DCC-2600 Bottom Cover Removed — Lower internals of the Cuisinart

Step v: Detect the coffee maker leak location.

Once you have the lesser encompass off you tin can search for the leak. I've heard of people discovering a leak in the aluminum heating chemical element likewise equally the safe tubing. Quickly I was able to run into a light-colored line on the top side of one of the hoses, just above where it connects to the heating chemical element:

Location of crack in hose — Cause of the leak-a cracked hose

With a little pressure on the hose you can definitely see that it is croaky all the way through–definitely the root cause of this leaking Cuisinart coffee maker:

Bending the hose to show the crack-the cause of this leaking Cuisinart coffee maker — The crack is evident now

Pace 6: Remove the wire hose clamp.

Clasp the hose clench and button it back on the heating chemical element, as seen below:

Step seven: Remove the heating element end of the cracked hose.

If yours cracked merely at the end of the heating element connexion y'all tin likely just bend the hose and it will pause off. Alternatively you could cut information technology off with a carpeting knife..

Piece of hose removed from the heating element — The slice I cut off the heater element

For those of you who want to replace the hose, I measured the heating chemical element pipe at 0.447:

Measuring the outer diameter of the heating element with a caliper — Outer diameter 0.447″

I estimate that the replacement hose should have an ID of 7/16″ = 0.4375 or 11 mm. I was not able to hands notice a replacement hose online.

Stride 8: Brand room to re-utilize the old hose.

I didn't accept any 7/16″ ID (inner-bore) high-temp nutrient grade hose lying around and then my first idea for solving my early morning pre-programmed caffeine habit was to put the old hose dorsum on. I idea almost cheating the hose off the other finish where it connects to the tank but I don't know how I would get up in under the tank in order to get information technology off and I was pretty concerned about damaging the brittle hose in the procedure. The hose is a one-half-inch shorter at present but it seemed like in that location was enough hose left to go it pushed on there far enough to make it work. To give the hose a shorter path I decided to cutting out some of the webbing inside the coffee pot:

Diagram of the plastic webbing I removed to make a shorter path for the hose — I cut out this plastic to make a shorter path for the hose

I drilled some holes with my cordless drill and then clipped out the plastic pieces remaining with my wire nippers:

Webbing removed for a straighter hose path — Now in that location is a straighter path for the hose

Pace 9: Reinstall the shorter hose on the heating element and reinstall the hose clamp.

You'll want to put the hose clench on get-go, before reinstalling the hose. I had to bend the hose clamp airtight a scrap considering it seemed to accept opened up in the removal process. I used some spit on the heating element pipe before attempting to push the hose on. I was only able to become the hose on well-nigh a maximum of 3/viii″ on.WARNING: I would not utilise whatsoever tools to squeeze the hose our you lot will probable damage what little hose y'all take left. Once y'all take the hose on, position the hose clench in the middle of the hose equally seen below:

Step 10: Reinstall the bottom comprehend.

I really didn't put the screws back into the bottom cover yet as I wanted to test it out for a while and am yet shopping for a replacement hose source. Let me know in the comments if you find a good source where you don't need to pay half the value of the coffee maker for ten feet of hose when all I demand is near a human foot.

And again, you can use a flat-tip screwdriver to reinstall those security torx screws!

The coffee maker is working but fine now so that is overnice to be able to breathe life dorsum into what could have been the end of this appliance.

Share YOUR repair!

Accept y'all repaired your leaking Cuisinart java maker? Did you lot effigy out a meliorate style to repair it? Have you found a good identify to purchase replacement hoses? Comments? Suggestions? Please go out them in the comments beneath!

Amazon Acquaintance Disclosure: As an Amazon Associate I earn from qualifying purchases. This ways if you click on an affiliate link and purchase the detail, I will receive an affiliate committee. The cost of the particular is the aforementioned whether it is an affiliate link or not. Regardless, I only recommend products or services I believe volition add value to Share Your Repair readers. Past using the affiliate links, you are helping support Share Your Repair, and I genuinely capeesh your support.